bieap.gov.in Electrical Technician Vocational Practical Question Bank : Andhra Pradesh State Institute of Education

Board : Andhra Pradesh State Institute of Vocational Education
Course : Vocational Practical | Electrical Technician
Document Type : Question Bank
Website : https://bie.ap.gov.in/

Download Model/Sample Question Paper :
1st Year : https://www.pdfquestion.in/uploads/7344-etyr1.pdf
2nd Year : https://www.pdfquestion.in/uploads/7344-etyr2.pdf

BIE Electrical Technician Vocational Practical Question

First Year:
Subject : Elements of Electrical Lab
Paper – I:
Time : 3 Hours
Max. Marks : 50

Related : Andhra Pradesh State Institute of Education Commercial Garment Technology Vocational Practical Question Bank : www.pdfquestion.in/7342.html

Section – I

1. Verify the ohms law by using ammeter, voltmeter in dc circuit or low voltage ac (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)
2. Verify the characteristics of DC series circuit (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

3. Verify the characteristics of DC parallel circuit (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)
4. Verify the laws of resistance by ohm meter, series test lamp by using different materials and loads (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

5. Verify the Kirchhoff’s by laws by using series parallel circuit (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)
6. Perform the testing of accumulator / battery by hydrometer and tongue tester on charging and discharging (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

7. Perform the measurement of power by wattmeter (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)
8. Perform the measurement of power in resistive load by voltmeter and ammeter (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

9. Perform the measurement of power factor by voltmeter, Ammeter and Wattmeter (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)
10. Perform the measurement of power factor by power factor meter (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

11. Perform the testing of energy meter (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)
12. Perform the measurement of energy by energy meter (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions).

13. Trace the magnetic lines for
(a) Bar magnet
(b) U Magnet. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

Section – II

Record : 5 Marks
Viva : 5 Marks

Subject : Elements of Electrical Lab
Paper – I:
Time : 3 hours Max. Marks : 50
Section – I 1 x 40 = 40 Marks:
5. Verify the Kirchhoff’s by laws by using series parallel circuit (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

Section – II:
Record 5 Marks
Viva 5 Marks

Note : The serial numbers of the questions mentioned in are the serial numbers in question bank. In practical examination only the serial number of the questions will given, the examiner shall decode it with question bank and give the questions.

Elements of Electrical Lab

Paper – I:
Time : 3 hours Max. Marks : 50
Section – I:
Aim, Tools, Materials and Equipments : 5 Marks
Circuit diagram : 5 Marks
Order of performing the experiment : 8 Marks
Handling of tools : 5 Marks
Utilization of materials : 5 Marks
Procedure : 5 Marks
Precautions : 2 Marks

Section – II:
Result/Appearance/Presentation : 5 Marks
Record : 5 Marks
Viva : 5 Marks

Subject : Electrical Wiring and Workshop
Paper – II:
Time : 3 Hours Max. Marks : 50
Section – I 1 x 40 = 40 Marks:
1. (a) Prepare a straight joint by using 3/20 copper cable (Only practical)
(b) Make a wiring installation for one lamp controlled by one switch in surface conduit wiring. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

2. (a) Prepare a T. joint with 1/8 wire. (Only practical)
(b) Make a stair case wiring circuit by using surface conduit wiring. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions) (Only practical)

3. (a) Prepare a married joint by using 14/0.3 (1sq mm) copper cable.
(b) Make two lamps controlled by two switches by using conduit wiring. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions) (Only practical)

4. (a) Prepare a T. joint with 7/20 wire.
(b) Install wiring for control of one lamp and one socket outlet by separate switches. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions) (Only practical)

5. (a) Prepare a pig tail joint by using single strand aluminum cable
(b) Make a wiring for a three chamber godown. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions) (Only practical)

6. (a) Prepare a straight joint by using GI wire
(b) Install a series-parallel wiring circuit for control of two lamps by one switch in surface conduit wiring. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

7. Install and bed room wiring circuit by using surface conduit wiring. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

8. (a) Prepare a married joint by using 2-sqmm copper cable (Only practical)
(b) Make Flourescent lamp circuit cable. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

9. (a) Prepare a Tee joint with 7/20 wire. (Only practical)
(b) Install pipe earthing and test with test lamp. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)

10. Install a conduit wiring for making the connection of new ceiling fan with regulator. (Aim, Tools and Materials, Circuit Diagram, Procedure, Observations, and Precautions)