jpsc.gov.in Previous Question Paper Assistant Engineer : Jharkhand Public Service Commission

Organisation : Jharkhand Public Service Commission
Recruitment Name : Assistant Engineer
Document Type : Previous Question Paper
Year : 2018-2019
Website : https://www.jpsc.gov.in/sam_question_paper.php

JPSC Assistant Engineer Previous Question Paper

1. In reciprocating air compressor the method of controlling the quantity of air delivered is done by
(A) Throttle control
(B) Blow-off control
(C) Clearance control
(D) All of`the above

Related / Similar Question Paper : Bihar Public Service Commission Question Paper School Teacher

2. Heat transfer takes place according to the following law of thermodynamics
(A) Zeroth
(B) First
(C) Second
(D) Third

3. Heat transfer in liquid and gases is essentially due to
(A) Conduction
(B) Convection
(C) Radiation
(D) Conduction and Radiation

4. Which mode(s) of heat transfer does (do) not need a mat6rial medium ?
(A) Conduction
(B) Convection
(C) Radiation
(D) Convection and Radiation

5. As the temperature increases, the thermal conductivity of a gas
(A) increases
(B) decreases
(C) remains constant
(D) increase upto a certain temperature and then decrease

6. Heat conduction in gases is due to
(A) motion of electrons
(B) elastic impact of molecules
(C) mixing motion of the different layers of the gas
(D) electromagnetic waves

7. Indicate the metal with highest thermal conductivity
(A) Steel
(B) Silver
(C) copper
(D) Aluminium

8. Identify the very good insulator
(A) Sawdust
(B) Glass wool
(C) Cork
(D) Asbestos sheet

9. Fins are provided on heat transforming surface in order to increase
(A) heat transfer area
(B) heat transfer coefficient
(C) temperature gradient
(D) mechanical strength equipment

10. Finned surfaces have improved rate of heat dissipation due to
(A) decrease in ambient temperature.
(B) increase in the surface area exposed to the surrounding.
(C) increase in the corrective film coefficient.
(D) All of the above

11. An increase in fin effectiveness is caused by high value of ,
(A) convective coefficient
(B) thermal conductivity
(C) Circumference
(D) a)and(c)

12. Transient conduction means
(A) very little heat transfer.
(B) heat transfer for a short time.
(C) heat transfer with a very small temperature difference.
(D) conduction when the temperature at a point varies with time.

13. In the lumped parameter model, the temperature variation with time is
(A) Linear
(B) cubic
(C) Exponential
(D) Sinusoidal

14. Heat transfer by Radiation is encountered least in
(A) Boiler furnace
(B) Insulated steam pipe
(C) Electric bulb
(D) Nuclear reactor

15. Absorptivity of a body is equal to its emissivity
(A) for a polished body
(B) under thermal equilibrium condition
(C) at one particular temperature
(D) at shorter wavelengths

16. The emissivity is likely to be higher in case of _
(A) Rubber
(B) Paper
(C) Carbon
(D) Iron oxide

17. The emissivity and the absorptivity of a real surface are equal for radiation with identical temperature and wavelength. This law is referred as
(A) Lambert’s low
(B) Krichoff’s law
(C) Planck’s law
(D) Wien’s displacement law

18. Which parameter should be highest for a radiation shield ?
(A) Absorptivity
(B) Reflectivity
(C) Transmissivity
(D) Emissivity

19. The gray body shape factor for radiant heat exchange between a small body (impassivity 0.4) in a large enclosure (impassivity 0.5) is
(A) 0.1
(B) 0.2
(C) 0.4
(D) 0.5

20. Free convection heat flow depends on all of the following, except :
(A) Density
(B) Coefficient of viscosity
(C) Gravitational force
(D) Velocity

Instructions For Candidates

1. Please do not open this Question Booklet until you are told to do so.
2. Candidate must fill up the necessary information in the space provided on the OMR answer sheet before commencement of the ,examination.
3. Answer sheet will be processed by electronic device. Invalidation of answer sheet due to incomplete / incorrect filling of relevant circle of Roll No. and Question Booklet Series in the OMR answer sheet shall result in cancellation of candidature. Any deficiency in filling up OMR answer sheet will be the sole responsibility of the candidate.
4. An example is given below how to fill / mark (darken) Roll No. 41311706 and Question Booklet Series -8. Accordingly, you have to fill / mark (darken) the Roll No. and Question Booklet Series given to you in your OMR answer sheet.
5. For marking the correct answer, darken one circle by BLUE BALLPOINT PEN only.
6. Please do not mark (darken) more than one circle. Darkening more than one circle against an answer will be treated as wrong answer.
7. Do not detach any leaf from this Question Booklet After the examination, hand over the OMR answer sheet to the Room Invigilator. You are allowed to take the Question Booklet and carbon copy of the OMR answer sheet after examination is over.
8. Each question carries 2 marks. There is no negative marking for any wrong answer.
9. Possession and use of calculator, Mobile phone, Pager or any other electronic gadget is strictly prohibited in the Examination Hall.
10. Please abide by the instructions above and those given on the OMR answer sheet, failure to comply these instructions will be sole responsibility of the candidates.

Download Question Paper

Assistant Engineer Question Paper – https://www.pdfquestion.in/uploads/pdf2024/42485-q.pdf