College : Vardhaman College Of Engineering
Degree : B.Tech
Semester : I
Subject : Engineering Drawing
Document type : Question Paper
Website : vardhaman.org
Download Previous / Old Question Papers :
June – 2014 : https://www.pdfquestion.in/uploads/vardhaman.org/6296-BT1S9JUNE14.pdf
February – 2014 : https://www.pdfquestion.in/uploads/vardhaman.org/6296-BT1R13FEB14.pdf
December – 2013 : https://www.pdfquestion.in/uploads/vardhaman.org/6296-BT1S-DEC13.pdf
July – 2014 :https://www.pdfquestion.in/uploads/vardhaman.org/6296-BT1S3JULY14%20R11A.pdf
Engineering Drawing Question Paper :
VARDHAMAN COLLEGE OF ENGINEERING
(AUTONOMOUS)
B. Tech I Semester Supplementary Examinations July – 2014
(Regulations : VCE-R11A)
(Common to Mechanical Engineering, Aeronautical Engineering & Civil Engineering)
Date : 09 July, 2014
Time: 3 hours
Max Marks: 75
Related : Vardhaman College Of Engineering Basic Electrical & Electronics Engineering B.Tech Question Paper : www.pdfquestion.in/6295.html
Answer ONE question from each Unit
All Questions Carries Equal Marks
All parts of the question must be answered in one place only
Unit – I :
1. a) On a Russian map, a scale of versts is shown. On measuring it with a metric scale, 150 versts are found to measure 15 cm. construct comparative scales for the two units to measure upto 200 versts and 200 km respectively. Take 1 verst = 1.067 km. 8M
b) A theodolite has main scale plate of 240 mm diameter graduated to 0? to 360? with the vernier scale to read degree and minute. The main scale can read to accuracy of 0.5? and the vernier is to read one minute. Draw the scale. 7M
2. A circular disc of 40mm diameter rolls outside another circle of 120mm diameter for one revolution. Draw the path traced by a point, which is at a distance 25mm from the centre of the rolling circle. 15M
Unit – II :
3. The front view of a straight line AB is 60 mm long and is inclined at 60? to the reference line xy. The end point A is 15 mm above HP and 20 mm in front of VP. Draw the projections of the line AB if it is inclined at 45? to VP and is situated in the first quadrant. Determine its true length and inclination with HP. 15M
4. A straight road going uphill from a point A, due east to another point B, is 4 km long and has a slope of 15?. Another straight road from B, due 30?east of north, to a point C is also 4 km long but is on ground level. Determine the length and slope of the straight road joining the points A and C. Take scale, 10 mm = 0.4 km. 15M
Unit – III :
5. A square ABCD of 50 mm side has its corner A in HP, its diagonal AC inclined at 30? to HP and he diagonal BD inclined at 45? to VP and is parallel to HP. Draw its projections. 15M
6. A pentagonal prism is resting on one of the corners of its base on the HP. The longer edge containing that corner is inclined at 45o to the HP. and the vertical plane containing that edge and the axis are inclined at 30o to the VP. Take the side of base 45mm and height 70mm. Draw the projections of the solid. 15M
Unit – IV :
7. A pentagonal prism, side of base 25mm and axis 60mm long , rests with one of the edges of its base on HP. Its axis is inclined at 30oto HP and parallel to VP. It is cut by a horizontal section plane passing through the highest corner of the base. Draw the sectional top view. 15M
8. A cone base 50mm diameter and axis 65mm long, rests with its base on HP. It is cut by a section plane perpendicular to VP, inclined at 45o to HP and passing through a point on the axis 35mm above the base. Draw the sectional top view and the true shape of section. 15M
Unit – V :
9. A cone, base 54mm diameter and height 72mm, rests with its base on HP.A section plane perpendicular to HP and inclined at 25o to VP cuts the cone at a distance of 13.5 mm fromthe axis. Draw the sectional front view and develop the lateral surface of the remaining portion of the cone. 15M
10. Draw the development of the lateral surfaces of a cone of base diameter 60 mm and axis 70 mm long when it is resting with its base on HP. It is cut by a section plane which is perpendicular to VP and inclined at 45? to HP and bisects the axis. 15M