Orgnisation : Council For Indian School Certificate Examinations
Exam :ICSE (Class X) Technical Drawing
Document type : Question Paper
Website : cisce.org
Download Sample/Model Question Papers : https://www.pdfquestion.in/uploads/cisce.org/5895-Technical%20Drawing.pdf
CISCE Technical Drawing Question Paper
Answers to this Paper must be written on the paper provided separately.
You will not be allowed to write/draw during the first 15 minutes.
This time is to be spent in reading the question paper.
Related : Council For Indian School Certificate Examinations ICSE Yoga Question Paper : www.pdfquestion.in/5900.html
The time given at the head of this Paper is the time allowed for writing the answers. Attempt five questions in all. You must attempt three questions from Section A and two questions from Section B.
The questions must be answered in full scale. All construction lines must be shown. All dimensions are in millimetres unless specified otherwise. The intended marks for questions or parts of questions are given in brackets [ ].
SECTION A : (42 Marks)
Attempt any three questions from this Section
Question 1 :
The distance between two stations A and B is 100 kilometres. Its equivalent distance on the railway map measures only 2.5 cm. Find the Representative Fraction of the scale. Draw a diagonal scale to show a single kilometre.
Indicate on the same scale the following distances
(a) 577 km.
(b) 455 km. [14]
Question 2 :
(a) Describe an equilateral triangle about a circle of 70 mm diameter. [4]
(b) Draw a regular pentagon of side 55 mm and inscribe in it the same number of equal circles as the sides of the pentagon, each circle touching one side of the pentagon and two of the other circles externally. [5]
(c) Draw the AUXILIARY TOP VIEW of the square pyramid shown in Figure 1 given below. The auxiliary plane RxRy is inclined at 45° to the H.P.
Given :
Length of the side = 40 mm
Height = 85 mm [5]
Question 3 :
Draw the front view, the top view and the left hand side view of a hexagonal prism, having its base on the H.P (Horizontal Plane) and one of the edges of the base is inclined at 60° to the V.P (Vertical Plane).
Use the FIRST ANGLE method of projection. Also draw the development of the lateral surface of this prism.
Given :
Side of the base = 50 mm
Length of the axis = 75 mm [14]
Question 4 :
Copy Figure 2 given below using a scale of 1:1. [14]
Question 5 :
Refer to Figure 3 given below. Draw the ISOMETRIC VIEW. (Do not insert any dimensions). [14]
Section B : (38 Marks)
Attempt any two questions from this Section
Question 6 :
The isometric view of an object is shown in Figure 4 given below. Draw the following views in full scale using the THIRD ANGLE method of projection.
(a) The sectional front view. [Section A –A] [7]
(b) The side view from the left. [6]
(c) The top view. [6]
Question 7 :
The Figure 5 given below shows two views of a model. Draw
(a) The front view. [5]
(b) The top view. [7]
(c) The sectional side view from the left [Section A-A]. Use the FIRST ANGLE method of projection. [7]
Question 8 :
In Figure 6 given below a triangular pyramid of height 65 mm and base of side 50 mm is resting on its base on the ground with one of its base sides parallel to the V.P. It is cut by a sectional plane inclined at 45° to the H.P. and passes 35 mm above the base along the axis.
Draw :
(a) A sectional top view. [6]
(b) The true shape of the section. [6]
(c) The development of lateral surface. [7]
Syllabus :
THEORY – 100 Marks
1. Types of lines
(i) Border lines.
(ii) Outlines.
(iii) Dashed/ Dotted lines.
(iv) Centre lines.
(v) Extension lines or Projection lines.
(vi) Dimension lines.
(vii) Construction lines.
(viii) Cutting-Plane lines.
(ix) Section or Hatching lines.
(x) Short break lines.
(xi) Long break lines.
The names of different lines and their uses to be matched with the correct thickness and shade.
2. Dimensioning :
(i) Aligned system.
(ii) Unidirectional System.
3. Lettering and Numbering Upright capitals and small, freehand, single stroke, as used in Engineering drawing, and between, the correct guide lines.
4. Sheet Layout :
Basic – draw border lines, title block with name, sheet number, title etc.
5. Geometrical Constructions :
(a) Bisector of line segment.
(b) Division of a line segment into required number of parts/ proportional parts.
(c) Perpendicular and parallel lines.
(d) Bisection of an angle, trisection of a right angle/ straight angle.
(e) Congruent angle.
(f) To find the centre of an arc.
(g) Regular polygons up to six sides with simple methods using T-square and setsquares.