Name of the College : Kings College of Engineering
University : Anna University Chennai
Department : Mechanical Engineering
Subject Code/Name : GE1151 Basic Civil & Mechanical Engineering
Year : I
Semester : II
Degree : B.E
Website : kings.ac.in
Document Type : Question Bank
Download : https://www.pdfquestion.in/uploads/ki…560-EE1153.pdf
Kings Basic Civil & Mechanical Engineering Question Paper
Unit-I
Surveying And Civil Engineering Materials :
Part-A (2 Marks) :
1. What is surveying-
2. what is the objective of surveying-
3. what is the difference between a plan and a map-
4. what are the two major types of surveying
Related : Kings College of Engineering EE1153 Basic Electrical & Electronics Engineering B.E Question Bank : www.pdfquestion.in/1560.html
5. Differentiate between plane surveying and geodetic surveying-
6. How the surveying is classified based on purpose
7. State the principles of surveying.
8. What are the accessories used in chain surveying-
9. Define bearing of a line.
10. What are the systems of bearing
11. What is meant by local attraction & state its effects-
12. Define leveling and state its objectives
13. Define benchmark and state its effects
14. How rocks are classified-
15. What is quarrying & dressing of stones
16. What are the uses of stones-
17. State the uses of cement-
18. State the properties of cement concrete.
19. What is proportioning of concrete-
20. Define workability of concrete.
Part-B (16 Marks) :
1. Explain with neat sketch prismatic compass and principles of compass surveying. (16)
2. Explain with neat sketch 20m chain and principles of chain surveying. (16)
3. The following staff readings were observed successively with level, the instrument having been shifted after second and fifth readings
0.870; 1.635; 2.135; 1.280; 2.980
3.125; 0.120; 1.825; 2.765; 2.015
the first reading was taken with the staff held upon a bench mark of elevation + 100.00. Enter the readings in level book and final reduced levels. Apply the usual checks. Find also the difference in level between the first and last points (16)
4. What are the requirements of good building stone & state important varieties of Building stones (16)
5 The following perpendicular offset were taken at 10 meter intervals from an Survey line to an irregular boundary line 3.145m, 4.30m, 8.20m, 5.60m,7.60m, 4.2m, 5.6m, 4.3m. Calculate the area enclosed between the survey line, the irregular boundary line, and first and last offsets by the application of
a) Average ordinate method b) Trapezoidal rule and c) Simpson’s rule (16)
6. What are the different types of cement- Explain the properties and uses- (16)
7. What are the different types of steel- Explain the properties and uses- (16)
Unit-II
Building Components And Structures :
Part-A :
1. State the objectives and requirements of good foundation-
2. Differentiate between shallow foundation and deep foundation.
3. Define bearing capacity of soil.
4. How the stone masonry is classified-
5. Define the following terms.
i) Corbel
ii) Cornice
iii) Coping
iv) String course
v) Through stone
6. Compare stone masonry and Brick masonry
7. Why bonding in brick wall is essential-
8. State the special features of English and Flemish bond.
9. Define beam, column and Lintel.
10. Classify the types of column based on its conditions.
11. State the purpose of plastering.
12. Define Dam, Bridge and classify them
13. What are the basic components of a bridge-
14. What is the purpose of reinforced concrete-
15. Define factor of safety.
Part-B (16 Marks) :
1. a. List the six important points to be considered while selecting a site for construction of Dam.
b. Explain differential leveling with a neat sketch.
2. Explain with neat sketch the different types of piles.
3. List out the different types of bond in brick wall and explain any three in detail.
4. Draw a neat sketch of a reinforced cement concrete column and explain.
5. Explain the types of floor suitable for residential and commercial building.
6. Explain briefly the different types of pitched roof coverings.